- Joined
- Aug 28, 2007
- Posts
- 1,946
Posting this here since there are a few owners of these cabs on the forum.
(From the manual, just missing the pictures , don't really need them).
To Lower the Monitor Cabinet
1. Remove the two harness covers, found below the control panel, on the inside surface of each left and right upright. Store the covers and hardware in a safe place. They are used in the monitor up position only.
2. Remove the plastic caps covering the UP position lock bolts (1/2-13 x 1-12 socket head cap screws.) There is one of these caps on each side of the game, located on the outside face of each upright, and are labeled as, "LOCK-UP POSITION BOLT".
3. Using the 3/8" Allen wrench provided with the game, carefully remove the two Up-position lock bolts. One from each side of the game. CAUTION! DO NOT DROP THE BOLTS INSIDE THE UPRIGHTS.
Set these bolts to the side, as they will be used in the lock-down position.
4. Using three people, one on either side of the game, and one at the rear of the cabinet, grip the monitor cabinet under the front corner of control panel and the rar corner of the monitor cabinet, as indicated by labels that read, "GRIP HERE". While two people gently lift at the sides, the third person at the rear of the cabinet pulls upward and pushes the top of the cabinet forward. As soon as the top of the cabinet moves forward about an inch, allow the monitor cabinet to slowly slide down until it stops. Make sure htat no narnesses are pinched as the monitor cabinet moves down.
CAUTION!
DO NOT LET ANYTHING GET IN THE WAY OF THE MONITOR AS IT SLIDES DOWN. DOING OTHERWISE COULD RESULT IN DAMAGE OR INJURY.
5. Remove the plastic caps covering the DOWN position lock boltholes. Insert and tighten the lock bolts. Care must be take to NOT CROSS-THREAD THE LOCK BOLTS. DO NOT TIGHTEN ONE WITHOUT THE OTHER BEING IN PLACE. MOVE THE MONITOR CABINET AS REQUIRED TO OBTAIN PROPER HOLE ALIGNMENT.
CAUTION!
NEVER LEAVE THE LOCK BOLTS OUT OF THE CABINET. THEY MUST BE INSTALLED TO PREVENT ACCIDENT OR INJURY.
(From the manual, just missing the pictures , don't really need them).
To Lower the Monitor Cabinet
1. Remove the two harness covers, found below the control panel, on the inside surface of each left and right upright. Store the covers and hardware in a safe place. They are used in the monitor up position only.
2. Remove the plastic caps covering the UP position lock bolts (1/2-13 x 1-12 socket head cap screws.) There is one of these caps on each side of the game, located on the outside face of each upright, and are labeled as, "LOCK-UP POSITION BOLT".
3. Using the 3/8" Allen wrench provided with the game, carefully remove the two Up-position lock bolts. One from each side of the game. CAUTION! DO NOT DROP THE BOLTS INSIDE THE UPRIGHTS.
Set these bolts to the side, as they will be used in the lock-down position.
4. Using three people, one on either side of the game, and one at the rear of the cabinet, grip the monitor cabinet under the front corner of control panel and the rar corner of the monitor cabinet, as indicated by labels that read, "GRIP HERE". While two people gently lift at the sides, the third person at the rear of the cabinet pulls upward and pushes the top of the cabinet forward. As soon as the top of the cabinet moves forward about an inch, allow the monitor cabinet to slowly slide down until it stops. Make sure htat no narnesses are pinched as the monitor cabinet moves down.
CAUTION!
DO NOT LET ANYTHING GET IN THE WAY OF THE MONITOR AS IT SLIDES DOWN. DOING OTHERWISE COULD RESULT IN DAMAGE OR INJURY.
5. Remove the plastic caps covering the DOWN position lock boltholes. Insert and tighten the lock bolts. Care must be take to NOT CROSS-THREAD THE LOCK BOLTS. DO NOT TIGHTEN ONE WITHOUT THE OTHER BEING IN PLACE. MOVE THE MONITOR CABINET AS REQUIRED TO OBTAIN PROPER HOLE ALIGNMENT.
CAUTION!
NEVER LEAVE THE LOCK BOLTS OUT OF THE CABINET. THEY MUST BE INSTALLED TO PREVENT ACCIDENT OR INJURY.